Project Speedboat -- 95 Roadmaster M6 sleeper

**shownomercy** · 11-21-2016, 09:35 PM

Spray some bronzer on that and its good to go.

**Catmaigne** · 11-22-2016, 03:57 PM

Imma pretend I didnt see it...

Anyone want some headers? Lightly used, 200obo

Sent from my VS986 using Tapatalk

**Catmaigne** · 11-23-2016, 11:47 AM

Picked up a rear sway bar, manual seat rail for the drivers side, and rubber floor at the yard yesterday. If someone pukes or takes a dump on my floor I'm totally covered now.

Might also be converting to rear disc brakes.

Also, newly shortened driveshaft courtesy of Hartman Driveshaft in Reading.

Sent from my VS986 using Tapatalk

***SSlowBoat*** · 11-23-2016, 12:25 PM

Originally Posted by Catmaigne

Picked up a rear sway bar, manual seat rail for the drivers side, and rubber floor at the yard yesterday. If someone pukes or takes a dump on my floor I'm totally covered now.

Might also be converting to rear disc brakes.

Also, newly shortened driveshaft courtesy of Hartman Driveshaft in Reading.

Sent from my VS986 using Tapatalk

you wanna sell one of them? then i could have it shortened for my camaro lol. how much was it for shortening and balance?

***popo8*** · 11-23-2016, 01:39 PM

Hey man... i know u said u were interested in my ss springs. I just wanted to make sure u knew that I had cut half a coil out of the fronts.

LTXtech.com IS my drug...
OWNER/ADMIN

**Catmaigne** · 11-23-2016, 07:03 PM

Originally Posted by Tubby Z28

you wanna sell one of them? then i could have it shortened for my camaro lol. how much was it for shortening and balance?

I am going to be selling them but won't be cutting any deals though, trying to make some money back bc car is making me broke. Will probably throw them up on CL or ebay for $100ea and see what happens. And the shortening was $150. I gave him the wrong u-joints because the info on the impala forum was wrong and the ones he threw in were kinda pricey so the total cost went up $55~. Whole thing was $270 in all, not bad considering the Denny's/Inland Empire/PST are all $500+.

Sent from my VS986 using Tapatalk

**Catmaigne** · 11-23-2016, 07:08 PM

Originally Posted by popo8

Hey man... i know u said u were interested in my ss springs. I just wanted to make sure u knew that I had cut half a coil out of the fronts.

LTXtech.com IS my drug...
OWNER/ADMIN

I know, I'm only really interested in the rears honestly but will buy the whole set if you'd prefer. I will be running those and high rate Moog springs up front for something similar to the PPM autox but cheaper.

Sent from my VS986 using Tapatalk

**Catmaigne** · 11-23-2016, 07:15 PM

Fun fact about t56 swapped bbodies: You have to lift the motor this much after sliding everything forward to get the oil pan out... Gah

Sent from my VS986 using Tapatalk

***popo8*** · 11-23-2016, 07:26 PM

Originally Posted by Catmaigne

I know, I'm only really interested in the rears honestly but will buy the whole set if you'd prefer. I will be running those and high rate Moog springs up front for something similar to the PPM autox but cheaper.

Sent from my VS986 using Tapatalk

Ok... just wanted to make sure u knew. It goes in for the drop on monday.

LTXtech.com IS my drug...
OWNER/ADMIN

***SSlowBoat*** · 11-23-2016, 11:42 PM

Originally Posted by Catmaigne

Fun fact about t56 swapped bbodies: You have to lift the motor this much after sliding everything forward to get the oil pan out... Gah

Sent from my VS986 using Tapatalk

Or you just remove motor....

I still have that list of spring rates for moogs to copy or go a hair above the ppm autox springs. That was what i wanted to mimic too. All the springs can be had on amazon for dirt cheap

Sent from my SAMSUNG-SM-G935A using Tapatalk