hvac delete plates $40 plus shipping

[jakesz28]

I'm ordering these this week. I should have had them sooner. As soon as there in I'll post the pics and I need to get prices on shipping them.

.061 thick aluminum

$45 shipped

[93v8clone]

let me know when ya do as i need to do this .also this only loses the a/c portion of the hvac system right

[AChotrod]

I wish you had this a week ago!! Any Idea how hard it would be to do with the motor in the car?

[jakesz28]

I think it would be a pain to do with the motor in the car. I think it can be done. It's been a while but it can be done. I took mine out with the motor in the car. If you look at this picture there is a bolt to the left of the large hole that you need to get the bolt out of on the engine side of the firewall. I think I actually broke my heater box because I could get the bolt out at first. Now I know it is there.

http://i97.photobucket.com/albums/l211/jakesz28/1107012.jpg

As soon as the laser cutter gets them done I will be picking them up.


This is intended to remove both the heater and a/c. I think there have been a few people that used panel like this and modified it and the inside heater assembly to run heat and only remove the a/c.

[jakesz28]

Talked to the laser cutter today and I will be picking these up on Tuesday or Wednesday

[dsmawd350]

i just went to town on mine with a sawzall and ripped the fucker out with someone watching under the dash for wires

[AChotrod]

I want to leave the heat and just get rid of the part in the bay. Looks like that will require choppin it off and thats not gonna happen.

[95ztrey]

pm me prices a total with shipping to amarillo texas 79110 , just chopped mine out ;)

[jakesz28]

I picked these up and there ready to go.



http://i97.photobucket.com/albums/l211/jakesz28/63009003.jpg

[jakesz28]

I can sell these shipped for $45. So who needs them?

[jakesz28]

I got about 20 of these sitting here.

[Infamous Z]

I will order one in couple of weeks do u have a pic of it installed

[blackbird1084]

Hey Jake do you know what all needs to be done in order to keep the heater? I already have most of my a/c stuff out all that's left is the box. Oh and do you know how much the a/c box/core weighs?

[jakesz28]

I don't think it would be that hard. I think you will need some fiberglass cloth and resin to direct the heat in the right direction. If you remove the AC stuff from the engine capartment I think it will be noticable(what I'm talking about) Then you just need to mark out the heater lines and trim the cover.

There was a good thread on LS1tech a while back. I think it was MERV or MARV. He did the 6.0 swap but he is always posting in the LT1 section. But his thread if I remember right had some good pictures.

[jakesz28]

Heres a picture to help out


http://i103.photobucket.com/albums/m129/the_merv/BLOWERDUCT3.jpg

[blackbird1084]

Is that a pic of what needs to be done to keep the heater? If so I'm gonna start taking that stuff out and after I get it out I'll order one of these sweet block off plates from you.

[jakesz28]

Yes that is what it takes to leave the heat.

heres a before picture.

http://i67.photobucket.com/albums/h290/MWRalls/39.gif

[blackbird1084]

So in my quest to save weight (and in order to keep my heat) I gotta cut more stuff out? That's funny and awsome lol

[blackbird1084]

Hey jake where do i send the money?

[jakesz28]

PM sent

[ksmyss]

Do you still have one of these?

[jakesz28]

Yep I have them. $45 shipped.

[ksmyss]

you have a pm

[Ryan Stout]

Got mine today, looks good, thanks!

[ksmyss]

Got mine yesterday too. Thanx again.