84ta406
03-29-2009, 01:38 PM
1984 Pontiac Trans Am WS6
Engine
400ci sbc
Holley 750DP carb 4779-6
1" Phenolic "clover" spacer
Edelbrock Performer RPM manifold
World Products Sportsman II heads, heavily ported and polished, 10* locks and retainers, Comp cams Springs, pushrod guides, seats. ARP 7/16" rocker studs, fully setup for a roller cam.
Custom grind Comp cams retrofit Hydraulic roller camshaft .586/.562 lift 236*/248* duration @.050 113LSA
Comp cams Pro Magnum lifters
Comp cams Pro Magnum Pushrods
Comp cams Pro Magnum Roller rockers 1.5
509 casting block (rarest 400 block)
Cast pistons, rods and crank
Pete Jackson gear drive timing
HEI distributor
MSD 6AL box
MSD Rev Limiter Selector box 6000-8200
MSD supercomp plug wires
Autolite # 26's
Exhaust:
Hooker Longtube headers
Hooker ORY pipe
TSP Rumbler catback
Drivetrain:
TH700r4, Redneck performance 3200 stall converter, Valvebody has been adjusted.
4th gen Aluminum Driveshaft
GM 7.5" 10 bolt rearend with 3.73's
Full disk brakes
16" Formula wheels
Suspension:
Moroso 90/10 trick springs in the front
UMI tubular LCA's
Misc. other stuff:
Edelbrock electric fuel pump #1791 and relay kit #1795
Powermaster XS torque mini starter(required for LT's)
Electric fan setup
Stock tail light setup along with a set of 84 Anniversary edition tail lights(1 of 1500 sets)
RECARO rear seats(1 of 1500 sets)
5" Autometer Sport comp silver tach w/ mini shift light
Autometer 2 5/8" Fuel pressure guage mounted on cowl
Dual guage A-Pillar pod
-Cyberdyne Digital tranny temp
-Cyberdyne Narrowband O2
Dual Guage pod under the dash
-Sunpro water temp guage
-Sunpro Oil PSI guage
Pioneer 4X6 IN-dash speakers
A/C delete
Custom switch panel for Electronics
External tranny cooler
http://i164.photobucket.com/albums/u12/84stroker/Mycaaah.jpg
http://i164.photobucket.com/albums/u12/84stroker/Car/IMG_2607.jpg
I know I'm forgetting a few things.. Body is CLEAN, paint itsnt too great though. Motor runs like a top and with the Hyd. roller cam it feels so strong. I'm asking $5000, possibly trade for a M6 LT1 Trans Am.
Engine
400ci sbc
Holley 750DP carb 4779-6
1" Phenolic "clover" spacer
Edelbrock Performer RPM manifold
World Products Sportsman II heads, heavily ported and polished, 10* locks and retainers, Comp cams Springs, pushrod guides, seats. ARP 7/16" rocker studs, fully setup for a roller cam.
Custom grind Comp cams retrofit Hydraulic roller camshaft .586/.562 lift 236*/248* duration @.050 113LSA
Comp cams Pro Magnum lifters
Comp cams Pro Magnum Pushrods
Comp cams Pro Magnum Roller rockers 1.5
509 casting block (rarest 400 block)
Cast pistons, rods and crank
Pete Jackson gear drive timing
HEI distributor
MSD 6AL box
MSD Rev Limiter Selector box 6000-8200
MSD supercomp plug wires
Autolite # 26's
Exhaust:
Hooker Longtube headers
Hooker ORY pipe
TSP Rumbler catback
Drivetrain:
TH700r4, Redneck performance 3200 stall converter, Valvebody has been adjusted.
4th gen Aluminum Driveshaft
GM 7.5" 10 bolt rearend with 3.73's
Full disk brakes
16" Formula wheels
Suspension:
Moroso 90/10 trick springs in the front
UMI tubular LCA's
Misc. other stuff:
Edelbrock electric fuel pump #1791 and relay kit #1795
Powermaster XS torque mini starter(required for LT's)
Electric fan setup
Stock tail light setup along with a set of 84 Anniversary edition tail lights(1 of 1500 sets)
RECARO rear seats(1 of 1500 sets)
5" Autometer Sport comp silver tach w/ mini shift light
Autometer 2 5/8" Fuel pressure guage mounted on cowl
Dual guage A-Pillar pod
-Cyberdyne Digital tranny temp
-Cyberdyne Narrowband O2
Dual Guage pod under the dash
-Sunpro water temp guage
-Sunpro Oil PSI guage
Pioneer 4X6 IN-dash speakers
A/C delete
Custom switch panel for Electronics
External tranny cooler
http://i164.photobucket.com/albums/u12/84stroker/Mycaaah.jpg
http://i164.photobucket.com/albums/u12/84stroker/Car/IMG_2607.jpg
I know I'm forgetting a few things.. Body is CLEAN, paint itsnt too great though. Motor runs like a top and with the Hyd. roller cam it feels so strong. I'm asking $5000, possibly trade for a M6 LT1 Trans Am.