another engine bay by Speed Inc.

[Speed Inc.]

before :

http://i120.photobucket.com/albums/o184/svtspeed04/carlos001.jpg

after :

http://i120.photobucket.com/albums/o184/svtspeed04/carlos044.jpg

ECU relocated
MSD relocated
Harness relocated
AN fuel line conversion and relocation
holes welded and engine bay repainted
Elbow modified and N20 nozzles relocated
IAT relocated
! power steering w/ use of our alternator kit
! heater core lines
Battery relocated

looking at an LS1 induction setup soon as well which will really finish off the engine IMO

details on car are at a min. for now :secret2: 388 /H/R/Brodix/12 bolt/TH400/stock ECU

[Formula383]

OH THAT'S PURDY!!

[devonsZ28]

nice

[AChotrod]

SEXY TIME!!!! ooooooooh yeahhhh!!!!!!!!!!!

[Formula383]

Well, I can tell it's a bird by the hood and headlights. I wonder who's it could be?????

[Fastbird]

Wow, that's really nice under there!

[941le]

clean as hell!

[armyb95zxc]

that's tight!!!

[Speed Inc.]

thanks

since I have done my engine bay we have done 2 now and I must say we are happy with the results :)

[YZF]

Looks amazing!!1!

[Formula383]

thanks

since I have done my engine bay we have done 2 now and I must say we are happy with the results :)

I wish you could come to TX and do mine!

[Speed Inc.]

Kyle your car looks great already

[AChotrod]

so is that a freebie after you spend a certain amount of money at speedinc?

[windsofthor]

Looks like some good work.


I love clean bays.

[Speed Inc.]

so is that a freebie after you spend a certain amount of money at speedinc?

oh sure...this is usually done with clutch install :laugh:



Looks like some good work.


I love clean bays.

thanks

[CARLOS]

That engine bay looks familiar :detective:

[Speed Inc.]

That engine bay looks familiar :detective:

I bet it does :cool:

[grn95t/a]

looks mean as hell when its that clean, all buisness!


on aside note, whats the chance of you telling me how long the fuel lines need to be made? i would love to get ride of those ugly ass factory ones.

[Camaro_94]

Looks awesome!!! :drool:

Great job!

[chevy42083]

That engine bay looks familiar :detective:

So does your sig pic :whistle:

[KLaBZ28]

Wooooooooooooowwww, I want to do this to mine... :(

[fast lt1]

looks real nice

[AChotrod]

oh sure...this is usually done with clutch install :laugh:
Awesome! Shall see ya soon!!!!!!!!!!!!

[Standard-Z]

Wooooooooooooowwww, I want to do this to mine... :(

Same here. Not enough $$$

Or I would be happy this 1.:D
http://i76.photobucket.com/albums/j34/Standard-Z/picture0586ip-1.jpg

[1hottcamaro]

that looks amazing!!!

[Camaro_94]

If you dont mind me asking, how long did that take you from start to finish? Once again, awesome job! :claps:

[Speed Inc.]

thanks

probably 15 hrs on the detail end of things with having the motor out

[Camaro_94]

thanks

probably 15 hrs on the detail end of things with having the motor out

WOW!!! All the hard work definately shows on it!

[Toronto_LT1]

very nice!!good job!
i want my engine bay to look like that someday

[Speed Inc.]

thanks again for the kind words

[ksmyss]

looks mean as hell when its that clean, all buisness!


on aside note, whats the chance of you telling me how long the fuel lines need to be made? i would love to get ride of those ugly ass factory ones.
i cut about 2 ft off mine.

[1FASTSS]

When Larry did mine last spring I would say they are probably 2-5' pieces. They run from where the hard line ends next to trans and run up near the firewall over to the FPR. I'm sure he'll chime in before too long.

[Speed Inc.]

little over 6'

[CamaroZGuy]

looks Awesome!

[Speed Inc.]

thanks