Lets see your custom switch panels!

[MeanTA]

Im getting ready to do my interior overhaul. Since the last major parts needed has been ordered.

My HVAC is deleted and Im wanting to put my switched in the blank spot where the controls was.

So give me some pics and idea:)

[popo8]

Is this only for TA owners?

[MeanTA]

Is this only for TA owners?

anyone can post. looking to see if anyones setup can give beenme a idea. i keep bouncing around layouts and ideas. but can't nail a idea down

[popo8]

Mine fills the old casette storage area... its not really a switch panel, although it does house the switch the changes my horn button to my line lock.... and back. It also houses the dial to set the RPM for my pillar mounted shift light , as well as a large face Oil Pressure guage, for added security.

[McCauleyWB]

Here's mine. I only kept the cigarette lighter because I wired my garage door opener to it.

14692

[MeanTA]

So far i am only needing 4 switches. WP,Fans,line lock arming,fog lights.

Im moving my momentary line lock switch to my grant wheel. I can't stand it on my shifter. With it being a short throw. and how i hold onto the shifter it makes it awkward

[jaysz2893]

Here's mine. I only kept the cigarette lighter because I wired my garage door opener to it.

14692
Is that the 6LE panel? I am thinking of moving mine off my pillar to this area, but I have 4 gauges (Oil, Fuel Pressure, Wideband, and Voltage) and I was going to move my lighter into the glovebox. I think I can get 4 in the panel if i cut up where the lighter used to be. Also where you get the CAMARO Z28 radio bezel?

[McCauleyWB]

Is that the 6LE panel? I am thinking of moving mine off my pillar to this area, but I have 4 gauges (Oil, Fuel Pressure, Wideband, and Voltage) and I was going to move my lighter into the glovebox. I think I can get 4 in the panel if i cut up where the lighter used to be. Also where you get the CAMARO Z28 radio bezel?

It is a 6LE panel, yes. I have two more gauges as well, but they are in a mustang style pod on the dash. I like being able to have my fuel pressure and wideband within eye-site. I don't think there is enough room to get more gauges on the 6LE panel. As it was, the two barely fit in the right side of the "cubby." You'd have to cut away some of your dash (the vertical separator between the cig lighter and right side) and I'm still not sure that would leave enough room.

The radio bezel is from humount.com.

14694

[firebird_1995]

Where does one get this 6le panel?

[Badbird_96]

http://6litereaterdesigns.com/store/

[popo8]

Mine is made from the inside sheet metal from the gas door of a 1985 Chevy Pickup, with a piece of 2.25 exhaust welded to it and cut on an angle to mount the guage.

[firebird_1995]

Your switch say "line lock" on one throw and "horn" on the other. What's that all aboot

[popo8]

Your switch say "line lock" on one throw and "horn" on the other. What's that all aboot

i flip it one way, and my horn button is my LINE LOCK... and no horn.
I flip it the other way and my horn button is my HORN....and not my line lock.
Its just a switch to change between the two...the steering wheel horn button is the activation for either.

Got the idea from my drag bike... I had a switch that would make the horn button either the horn...or the air shifter.

[firebird_1995]

Oh that's slick. Light turns green, let off the horn

[popo8]

Oh that's slick. Light turns green, let off the horn

Im 6spd , so its just for the sake of easier burnouts... but you get the idea.... and it makes it much easier to control on the wheel, with my thumb..., and I have never been a fan of that coily cord around the column....

[firebird_1995]

Im 6spd

Oh yea. But I guess it would work for launch control on an auto car too

[MeanTA]

Im 6spd , so its just for the sake of easier burnouts... but you get the idea.... and it makes it much easier to control on the wheel, with my thumb..., and I have never been a fan of that coily cord around the column....

That coil chord=Race car. lol

That's the route Im going. But Im also installing a grant wheel. And horn Button isn't convenient. But that's a genius idea!

[popo8]

... But that's a genius idea!

Thanks man... yes, with the stock steering wheel its great... would not be so great with a center horn button.

[NuckinFutz93]

http://i49.tinypic.com/2l8ghhj.jpg

I'm using that swith panel in the radio slot. I have bottle warmer,bottle on, NOS arm,tail/brake light kill, and LP switch on my panel.


Soon as I get it out of storage, my nos switches will operate the Meth injection.

[JPack]

Lets see... mine has trans brake, line lock, nitrous arm, bottle heater, purge, secondary pump, manual fan high and low.

http://i3.photobucket.com/albums/y77/jpack24/IMAG0806.jpg

[Fastbird]

http://i72.photobucket.com/albums/i177/Fastbird93/Purple%20Car/Build%20Pics/DSC_3670.jpg

Swapped to a 97 console, this holds a Spa Techniques dual Fuel Pressure/Boost Gauge, Line lock switch, secondary switch for a intercooler fan, and Alky Control Meth injection controls.

[MeanTA]

http://i72.photobucket.com/albums/i177/Fastbird93/Purple%20Car/Build%20Pics/DSC_3670.jpg

Swapped to a 97 console, this holds a Spa Techniques dual Fuel Pressure/Boost Gauge, Line lock switch, secondary switch for a intercooler fan, and Alky Control Meth injection controls.

where did you get the plate labeled? I would like to do that with mine.

[HAND HERPES]

Swapped to a 97 console, this holds a Spa Techniques dual Fuel Pressure/Boost Gauge, Line lock switch, secondary switch for a intercooler fan, and Alky Control Meth injection controls.

Wow thats nice and clean.


where did you get the plate labeled? I would like to do that with mine.

If I still worked at the CNC place I could of made this for you lol

[Fastbird]

where did you get the plate labeled? I would like to do that with mine.

Jim Thelen, a.k.a. Beer99C5 from CorvetteForum.com did it for me. We were in cahoots a while back when I was offering them through my business. He hooked me up. Does outstanding work. If you contact him, tell him Sean (Fastbird) sent you.

[chile]

http://img.tapatalk.com/d/13/01/24/6u2emuma.jpg
I deleted the radio on made this.

[popo8]

Damn.... no tunes?

It does look good though!

[chile]

Thanks. I got rid of it a while ago to simplify things.

[popo8]

Thanks. I got rid of it a while ago to simplify things.

I thought about it...but i love my music... Im fact i have sirius added...lol


Larry (Popo8) Co-owner
LTXtech.com

[chile]

Nice. I have the song of a custom LE cam and I usually dont take long drives with it.

[NuckinFutz93]

Damn.... no tunes?



My 93 didn't come with a radio from the factory. LOL. Can't miss something that was never there.

[devildog1]

These came yesterday and wanted to post. Emblempros.com. Nice fit over the junk collector and lighter and price is the best part. Can be made for back lighting or labeled.

1680416805

[popo8]

These came yesterday and wanted to post. Emblempros.com. Nice fit over the junk collector and lighter and price is the best part. Can be made for back lighting or labeled.

1680416805

Wow...thats a nice peice.


Larry (Popo8) Co-owner
LTXtech.com