What times are you guys running on a cam only set up?

["NO SHOW"]

Sorry if this a repost, I did a search and nothing came up. Just curious as to what you guys are running in the 1/8 with full bolt ons and with cam only set ups?

Thanks in advance

[chevrolet423]

im curious to the answer to this questions as well... also what elevations are you running at when you made the pass. I heard its almost a full second from the drag strip here to the drags at sea level

[Wooshie]

You don't run 1/4 mile?

[chevrolet423]

i do im not cammed though! :(

["NO SHOW"]

I haven't had it on a 1/4 mile track yet but I have been to 1/8 mile because thats what's close around here, but I will be running a 1/4 this year.

No one has any times to post?

I was just curious to see what you guys are running with the LT1 in forth gens verses what my LT1 is running in my third gen.

[MEAN LT1]

I haven't had it on a 1/4 mile track yet but I have been to 1/8 mile because thats what's close around here, but I will be running a 1/4 this year.

No one has any times to post?

I was just curious to see what you guys are running with the LT1 in forth gens verses what my LT1 is running in my third gen.

12.66@111 on motor.

[95formula383lt1]

1st time ever with the car at the track on street tires hot lapped the the car 3 passes within a half hour pretty much an over heated the clutch then on my 4th pass over heated the car blew a HG. but heres the last pass.

R/T- 0.712
60ft- 2.494
330- 6.129
1/8- 9.089
MPH- 83.79
1000ft- 11.582
1/4- 13.690
MPH- 107.42

[Z28RacerLT1]

Back in the day I ran 11.80 @ 112
This was a hyd. roller. 232/242 .481/.502 on a 112.
Car weighed aroudn 3400 with driver
I had a turbo 400 with a brake. went 12.20 with 700R4 trans

This was done @ 2400 DA
I just found my old log book
run looks like this.
1.571
4.758
1/8th they didn't give a time
1/8th mph no time
9.811
11.807 @ 112.85

I ran 11.85 earlier in the day went 7.482 @ 90.39
Hope this helps

Ken

[tomsws6]

interesting, these times with mainly a cam. i have a cam for my Ty that I was going to install but was told it wont do anything until I do something with the heads and here you guys are knocking off a sec or more.

[Z28RacerLT1]

interesting, these times with mainly a cam. i have a cam for my Ty that I was going to install but was told it wont do anything until I do something with the heads and here you guys are knocking off a sec or more.

Yeah that time was the cam listed, 1.6 roller rockers, Valve train to match cam. Completely stock intake, short block, heads. I did have a 54mm Arizona Speed & Marine throttle body.

Ken

[19mike84]

im hoping for high 11's but im sure ill actually run low 12's with a hot cam, 3600 stall, 250-300ibs taken out and some sticky tires. either way ill be happy

[PHINES LT1]

7.73 @87ish with a 1.6x 60 ft. cam only 236/242 on a 110. lift is 550/560. tci 3500 stall, 12 bolt with 4.10s. not sure what the da was but couldnt have been too high. race weight was just under 3500.

[YZF]

I havent quite got around to putting in my cam yet, but at that time I will also be slapping on my LE3 heads so I still won't have any useful info. But with an awesome DA with minor bolt ons, the car went 12.61 at 109.

I can't wait to get the motor done!

["NO SHOW"]

7.73 @87ish with a 1.6x 60 ft. cam only 236/242 on a 110. lift is 550/560. tci 3500 stall, 12 bolt with 4.10s. not sure what the da was but couldnt have been too high. race weight was just under 3500.

Thats about what I am hoping for this year with the 4.30 gears, N/A.

[green96ta]

high 11s on a hot cam would be truly amazing. its hard to do with a cc503 and it makes 20-30 rwhp more than the hot cam....

[chevrolet423]

i just ran mine, 14.3 all day with cam and bolt ons! but also running 2.2 60fts all day long. Stock 3.42 gears and a T56

Elevation: 5800 ft

[VendettaV8]

i just ran mine, 14.3 all day with cam and bolt ons! but also running 2.2 60fts all day long. Stock 3.42 gears and a T56

Elevation: 5800 ft

isnt that a fair bit slow?

[96lt1m6]

165472[/SIZE]]isnt that a fair bit slow?

5800';)
and lack of traction

[chevrolet423]

isnt that a fair bit slow?

youd be surprised what impact elevation does and yes my 60fts are shitty, still need to work on them!

[Fixxer99TA]

Just ran the hawk today at NED and ended up with a 12.75 at 107.94 best cam only with bolt ons. Pretty good traction with the radials. The cam is only the hotcam, so nothing crazy there either. Im sure the car has more in it too when setup a little better (should be in the lower 12s with my current mods if Im not mistaken).

[gregrob]

13.1 @ 107

7000+ DA

[wyldcdn]

7.61, bolt on only car with high 1.6 60 foots. 342's on et streets, tranny upgraded with vig 2800. Looking to break stuff with new motor. LE2 heads, 305 cam 114, balanced blue printed all the good suporting stuff...wish me luck, I need to snap the axles into pieces:D

[tarheelsoldier]

I was doing 13.5 sec 1/4mi. That was just cam, TB, and exhaust. and the track was Zmax Dragway. Also pulled that out at Rockingham pretty consistantly too...

[Snkebait95]

Anyone know what full bolt on cc503 t56 would do with 3.23s? Cant wait to take mine to the track and find out, hopefully change to a 4.10 by then...