- Navigation
Results 1 to 9 of 9
Thread: Extended wheel studs
-
06-03-2016, 01:08 PM #1Lurker
- Status
- Offline
- Join Date
- Dec 2012
- Name
- Tommy N.
- Vehicle
- Silver 1996 Camaro Z28, Green 1996 Camaro Z28
- Location
- El Paso, TX
- Posts
- 946
Extended wheel studs
Hey guys I had a incident last week at the track and I have decided to get extended wheel studs anyone know which ones to get for our cars that are for weld racing lug nuts that are 12mm x 1.5. Thanks guys
Sent from my iPhone using Tapatalk96 Camaro Z28 Silver Mostly Stock, Full Exhaust
96 Camaro Z28 Green Big Cam, Quick Performance 9 Inch Rear End, Full Exhuast
-
06-03-2016, 02:58 PM #210 Second N/A Club
- Status
- Offline
- Join Date
- Sep 2008
- Name
- Josh
- Vehicle
- 96 Z28
- Location
- Holden, MO (KC)
- Posts
- 2,867
ARP makes a nice set, are you using the stock style lug nut (acorn) or shank style? Front or rear and what axles if rear? ARP #100-7708 is the 12mm X 1.5. I can do $14.99 per pack of 5 plus shipping if your interested.
-Josh
co-owner of BDBRacing.com
NMCA OC 9004
96, N/A 385, Holley EFI, Faceplated M6, AI TFS heads, LE SR cam, MWC Fab 9
10.16 @ 136 1.50 60'........still workin on that 60' shootin for 1.4's!
-
06-03-2016, 05:01 PM #3Long Live the Opti
- Status
- Offline
- Join Date
- Sep 2008
- Name
- Sean
- Vehicle
- 1999 Twin Turbo Corvette
- Location
- Fort Wayne, IN
- Posts
- 12,072
On that note, for what it's worth, you don't have to run a open ended acorn nut for street wheels either. The pic below is @BaddAss93TA 's car. I put a 12 bolt in with 3" studs in the back. Found these long aluminum head lug nuts at autozone and they worked perfectly.
Just in case you thought you had to give up your street wheels for the longer studs.
-
The Following User Says Thank You to Fastbird For This Post:
-
06-03-2016, 08:42 PM #4LTx Guru
- Status
- Offline
- Join Date
- Apr 2013
- Name
- Fred
- Vehicle
- 1994 Formula - SOLD
- Location
- Central NJ
- Posts
- 2,283
Which Weld wheels? Running spacers in the front? Here's a recent discussion on studs for the Pro-Stars w/ 5/16" spacer in front.
http://ltxtech.com/forums/showthread...s-advice/page2
Be careful w/ the closed end extra long lug nuts. I have 3" X 1/2"-20 studs on my 12-bolt, and the ZR1/GS street wheels. I got a set of the extra long closed end lugs, and the stud bottomed out on the closed end of the lug nut before reaching the recommended torque on the wheels. I drilled the closed end and then ran a 1/2" tap through the entire length of the nut, exiting through the bored hole in the cap. Actually ended up looking OK with the end of the stud just about even with the end of the lug.
Point is, make sure you get lugs that are long enough.... i.e. ask Sean for the part number.SOLD - GONE TO A (VERY) GOOD HOME ! - 94 Formula A3+1: 381ci forged stroker - Callies Stealth, Oliver 5.85 billet rods, BME nitrous pistons / CNC LT4 heads / CC solid roller / TH400+GearVendors OD / 4.11 Strange 12-bolt / 300-shot N2O / Spohn Suspension / roll bar / MoTeC M48 Pro engine management system /a few other odds 'n ends.
-
The Following User Says Thank You to Injuneer For This Post:
-
06-03-2016, 09:06 PM #5Lurker
- Status
- Offline
- Join Date
- Dec 2012
- Name
- Tommy N.
- Vehicle
- Silver 1996 Camaro Z28, Green 1996 Camaro Z28
- Location
- El Paso, TX
- Posts
- 946
Open shank and Weld RTS with a spacer in the rear
Sent from my iPhone using Tapatalk96 Camaro Z28 Silver Mostly Stock, Full Exhaust
96 Camaro Z28 Green Big Cam, Quick Performance 9 Inch Rear End, Full Exhuast
-
06-03-2016, 10:26 PM #6LTx Guru
- Status
- Offline
- Join Date
- Apr 2013
- Name
- Fred
- Vehicle
- 1994 Formula - SOLD
- Location
- Central NJ
- Posts
- 2,283
I thought the RT-S used a conical lug?
SOLD - GONE TO A (VERY) GOOD HOME ! - 94 Formula A3+1: 381ci forged stroker - Callies Stealth, Oliver 5.85 billet rods, BME nitrous pistons / CNC LT4 heads / CC solid roller / TH400+GearVendors OD / 4.11 Strange 12-bolt / 300-shot N2O / Spohn Suspension / roll bar / MoTeC M48 Pro engine management system /a few other odds 'n ends.
-
06-04-2016, 08:54 AM #7
According to Weld they do.
"- Requires conical lugs"
http://weldwheels.com/shop/street-st...ed-shells.htmlCorrelation does not imply causation.
Una salus victis nullam sperare salutem
-
06-04-2016, 08:56 AM #8Xtreme Member
- Status
- Offline
- Join Date
- Apr 2010
- Name
- Brian DeLuca
- Vehicle
- 1997 Trans Am WS6
- Location
- Piscataway, NJ
- Posts
- 1,297
Odd. Mine came with shanks/washers.
97 T/A Ram Air Convt - 10.2@140 / 777rwhp - Forever Dyno Queen
17 Corvette Z06 - 11.05 @ 125
17 GMC Sierra Denali Dmax
-
06-06-2016, 09:14 PM #9LTX Master
- Status
- Offline
- Join Date
- Nov 2013
- Name
- Corey
- Vehicle
- 94 Camaro z28
- Location
- new hampshire
- Posts
- 575
my RTS's came with conical open end lugs and I just picked up a set of ARP 3" studs (#ARP-100-7713)
Last edited by hokeplaya05; 06-06-2016 at 09:16 PM.
94 Z28 M6, 383 LT1, McLeod Twin Disk, MGW, SLP CAI, Pacesetter LTs w/ORY, E-cut out, Spintech 2OTL, Strano sways, BMR suspension, Viking coilovers, Solomon tuned
96 Chevy K1500, 5.7L Vortec, 4l60e, 14 bolt, Volant CAI, Pacesetter LTs, Spintech 6000, b&m, 33s- DD
Bookmarks