Become a ltxtech.com member, Click here to register!
CPT

  • Navigation

Search:

Type: Posts; User: AngryLT1

Search: Search took 0.00 seconds.

  1. Air pump is not pulley driven.

    Air pump is not pulley driven.
  2. Replies
    4
    Views
    466

    Maybe check out the TPS sensor, double check that...

    Maybe check out the TPS sensor, double check that you have the plug wires in the correct sequence and to the correct corresponding cylinder, try new plug wires. I would start with the plug wires...
  3. Replies
    1
    Views
    384

    SJM panhard and LCA's

    Is there anyone running the SJM panhard bar and LCA's? Just looking for some opinions on them. Looking at using them for my drag race setup.
  4. Replies
    14
    Views
    1,028

    Welcome sir! Got any mods on that Camaro?

    Welcome sir! Got any mods on that Camaro?
  5. Replies
    5
    Views
    487

    Ohio Crankshafts it is then! Joe- If it wasn't...

    Ohio Crankshafts it is then!

    Joe- If it wasn't for the fact that I am doing a ground up rebuild, I would. I have to save for my plans but, once I get to that point of engine work, I'll check back...
  6. I've ran NGK iridium's, but like what was said...

    I've ran NGK iridium's, but like what was said before, they are just a little too costly. lol.
  7. Replies
    5
    Views
    487

    Ohio Crankshaft and intake questions

    I am getting a parts list together and saving for a 383 build and was wanting some input on Ohio Crankshafts. I am going for a big hp build and was checking out their 3.750 4340 cranks. Their price...
  8. Replies
    11
    Views
    754

    Don't know if you have ruled this out or not, but...

    Don't know if you have ruled this out or not, but have you checked the heater core for leaks? Have you pressure tested the coolant system?
  9. Replies
    6
    Views
    449

    They have their arguable differences. I'm not...

    They have their arguable differences. I'm not gonna say that there is no difference between them, but I think it depends on interpretation. As far as the 355 build, I would recommend a rebuild kit,...
  10. Replies
    6
    Views
    449

    Since your car is a DD i would look into a 355...

    Since your car is a DD i would look into a 355 build. It would be way easier on the budget, yet provide a good base for some decent power over stock. With that many miles on it, plus the leaks that...
  11. Replies
    5
    Views
    346

    I would compression test it or do a cylinder leak...

    I would compression test it or do a cylinder leak down test. These tests will give you an idea as to the health of the engine as well as help identify problems such as head gasket failure.
  12. Replies
    8
    Views
    1,647

    I had a similar issue. I checked and rechecked...

    I had a similar issue. I checked and rechecked vacuum lines, checked the IAC and replaced it, still would idle at 2,000 rpm. Turned out to be a failed gasket on an EGR block off plate. Used some high...
  13. I live near Champaign IL, and I'm looking for a...

    I live near Champaign IL, and I'm looking for a spare block for an engine project. If I get the ok from the boss (the fiance haha!) I may come get it. It is a 3 1/2 hr. drive there and if I get the...
  14. First time at the track with the T/A. Tell me what ya think!

    Took the T/A to the track Friday and made 4 passes. I don't know how to tell if the times I ran were good for my set up or not so I wanted to get a few opinions about it. I have a 6 speed LT1 with...
  15. Thread: sig test

    by AngryLT1
    Replies
    0
    Views
    5,835

    sig test

    testing one two...testing
  16. Replies
    9
    Views
    431

    Welcome!

    Welcome!
  17. Replies
    4
    Views
    477

    Welcome!

    Welcome!
  18. Replies
    6
    Views
    460

    I have pacesetter LT's into a 3" summit x-pipe...

    I have pacesetter LT's into a 3" summit x-pipe setup on my T/A. The only thing I had to do is get a small 3" id to 3" od. extension from the auto parts store. I just bolted it up, and then took it to...
  19. Replies
    15
    Views
    798

    Thanks for the warm welcome everyone! It's nice...

    Thanks for the warm welcome everyone! It's nice to see so many fellow Illinois residents as well! lol!
  20. Replies
    15
    Views
    798

    Here are a few pics I have right now:

    Here are a few pics I have right now:
  21. Replies
    15
    Views
    798

    I am working on getting some pics up soon...

    I am working on getting some pics up soon hopefully! lol. I live in Homer, IL which is about 30 min. from Champaign.
  22. Replies
    15
    Views
    798

    New guy from IL

    Hey everyone! I'm new to the forum and I have a 94 T/A M6. It's got BMR LCA's, Eibach springs, SFC's, K&N intake kit, and Pacesetter LT's into 3" x-pipe. That's pretty much it; some weight reduction...
Results 1 to 22 of 23