Become a ltxtech.com member, Click here to register!
SSS

  • Navigation

Search:

Type: Posts; User: Gojira94

Search: Search took 0.00 seconds.

  1. Replies
    24
    Views
    7,318

    Thanks! I drove it for about 1/2 hour at sunset...

    Thanks! I drove it for about 1/2 hour at sunset around the rural roads where I live and it really rips now, despite the 2.73:1 rear. I would have liked to put the 3.42 from my M6 in it with a ring...
  2. Replies
    24
    Views
    7,318

    Resolved... probably

    Tentatively going to say it's resolved. But not how it thought it would be.

    Yes, the harness needed to be replaced due to the hidden issue with the TCC solenoid built into the harness. But that...
  3. Replies
    24
    Views
    7,318

    I picked up a new harness with TCC solenoid. BWD...

    I picked up a new harness with TCC solenoid. BWD S9844. Has Delphi printed on it in a couple places. Same manufacturer overseas makes a bunch of Delphi stuff these days, all the same. I tested the...
  4. Replies
    24
    Views
    7,318

    I tested all the solenoids except the PCS, will...

    I tested all the solenoids except the PCS, will have to dig up a 9V battery for that one, but I did check the resistance between the PCM pins that go to it (no direct 12V from pin E, only gets signal...
  5. Replies
    24
    Views
    7,318

    Lowering the trans a bit helped me get the socket...

    Lowering the trans a bit helped me get the socket wiggle I needed to drop the case connector through the case.I pulled all the solenoids and checked them again for resistance. Values in ohms are:
    ...
  6. Replies
    24
    Views
    7,318

    well, damned if I can get the case connector out...

    well, damned if I can get the case connector out of the case. I'd read that a 1 1/4" 12 pt socket is the way to go but I can't force it down onto the tabs to compress them. Trans is in the car,...
  7. Replies
    24
    Views
    7,318

    I fished the case connector and VSS pigtail up to...

    I fished the case connector and VSS pigtail up to the engine bay where I can work with it easily. I have a 1 1/4" socket to pop the case connector out of the case. I'm trying to get the pressure...
  8. Replies
    24
    Views
    7,318

    Finally have some pictures of the valve body/...

    Finally have some pictures of the valve body/ solenoid arrangement. I do see on one of them the valve body has 95 cast into it, and a number sequence that looks like 3678593 or 3678595 but my eyes...
  9. Replies
    24
    Views
    7,318

    I get 11.8 ohms, right in the middle of the spec...

    I get 11.8 ohms, right in the middle of the spec for 94-95's 3-2 spec of 9-14 ohms. The VSS is on the driver's side but that could have been moved when it was built. If it's a 96+ transmission after...
  10. Replies
    24
    Views
    7,318

    Thanks, Frank I'd almost give my left nut for...

    Thanks, Frank

    I'd almost give my left nut for a copy of the build sheet on this transmission, lol. Can you elaborate on the 3-2 valve lineup and what those forced downshift issues look like? Would...
  11. Replies
    24
    Views
    7,318

    Back from the dead thread. With the help of...

    Back from the dead thread.

    With the help of some folks who do lots of GM EFI tuning on another forum , it was determined that the tune was bad. The 94 PCM mask was still used and the tables that...
  12. Replies
    24
    Views
    7,318

    I haven't been able to spend any time with the...

    I haven't been able to spend any time with the car to get firm answers to helpful questions, sorry about that. Car's in an outbuilding at our old house, presently rented out (we reserved the...
  13. Replies
    24
    Views
    7,318

    Absolutely. Very much appreciated. Be back with...

    Absolutely. Very much appreciated. Be back with pertinent info ASAP.
  14. Replies
    24
    Views
    7,318

    In the past I've had difficulty getting the case...

    In the past I've had difficulty getting the case connector off without first supporting the tailshaft housing with a jack and unbolting the trans mount and letting it drop a little. But no big deal...
  15. Replies
    24
    Views
    7,318

    Correct- max line pressure and 3rd gear start...

    Correct- max line pressure and 3rd gear start mode, etc per GM ("soft landing mode"). I really need to check again to see if the code 84 is gone with everything connected. Thinking back on it, I may...
  16. Replies
    24
    Views
    7,318

    94 Car with 95(?) Transmission

    I already posted this at LS1Tech's LT1-LT4 forum, but thought I might have better luck here (apologies). Kind of long but I think I have all the details I know.

    I've got a 94 A4 that's been tuned...
  17. Replies
    4
    Views
    1,121

    New member in Clayton, NC

    Hi

    I've been a member of another forum for about 5 years, have looked to LTXtech for occasional information, finally joining. I have 2 94 Formulas, one built 94 M6 (with more always planned) and a...
Results 1 to 17 of 17