Second on Cometic if needing MLS. They are expensive, though.

Any idea what caused the rod to break? Material failure?

Nice looking engine BTW.

96-97? Price shipped to 90807?

Do you happen to have a stock cam?

Just pulled my engine due to blow head gasket and discovered a wiped cam lobe.

Looking to get a stock 96-97 camshaft to replace this one.

Please let me know your price+shipping to 90807.

I believe it is the HDX. I bought a low mileage one secondhand off the forum here years ago.

So BDB got back to me with a price of $1565 for the street twin with flywheel and weight kit. This is pretty much the same price as everywhere else. I am wondering if it is going to be a big enough...

I saw that tick has it listed under cts-v so I wasn't sure if that was correct. It did look like the right one, though. I asked BDB racing to price one so I will see what he says.

I currently have a Ram HD clutch on my LT1 but it is slipping when I go WOT at the higher end of the rev range. I am pushing a little over 400 torque to the wheels and want to get something that will...

I still need to think about what to do with my parts. I kind of want to sell the tranny to make back some money but harner makes a good point about keeping it so i can revert the car to original if...

No injuries. I was going 40-50 coming off of an interchange in the rain. started accelerating to highway speed but i gave it too much gas. Tires spun and i ended up in the wall to my right and then...

Not the best Thanksgiving weekend ever. Adjuster just determined my many years long project a total loss. Only put about 2000 miles on the new motor.

37260372613726237263

But there is always...

I decided to just shim the original starter and hope for the best. I got it to engage slightly more often than it would before i pulled the motor. I might try a stock flywheel after my car is shipped...

I have the entire engine out and transmission removed. The flywheel looks brand new.



With no shims I have the recommended .020"+ clearance. It only gets bigger with more shims. This is after...

This car has a fresh built LT1 (about 1500 miles) and almost all of the parts are new. For the last 500 or so miles, I have been having trouble getting the car started. After turning the key anywhere...

You should definitely be using a bore gauge for measuring clearances. I wouldn't trust plastigage with one of the most critical measurements in the engine.

On my 7k rpm engine I went with...

Does the noise increase with RPM or with vehicle speed? Try different putting it in first and second manually as you are going at whatever speed causes the noise to be loud. If it is RPM related then...

Just make sure you know what you want. He has a few different options as far as what you have in your car such as transmission and electric water pump and others. He can help you decide if you need.

I would also recommend the SSD swap. makes the computer run so much smoother that you will never want to go back.

look just like the ones i pulled out of my engine. Can't guarantee they are stock though.

BP usually takes a few days to respond but he will pretty much always get back to you. I bought mine a few years ago and he still answers my emails when i have questions. I got one of his really...

I am using hptuners for my 24x but i ordered a cheap used one on cowboom.com. if you check slickdeals.net they usually have coupons and whatnot for that site. i got an asus 15 inch touchscreen laptop...

Yea I thought it could be the A/F. My wideband wasnt calibrated recently before I did that video so I will see what it logs after I do that and hook it up to hptuners. I have a new iacv so it is...

Its no problem. I just have the heater bypassed right now until I get the hoses. I dont exactly need the heater in hawaii.

It will run the second time I try and stay idling so i feel that isn't the problem. I could be wrong of course. I didn't show a CEL but I didn't get a chance to scan it because I am on a ship and...