Become a ltxtech.com member, Click here to register!
BP-Automotive

  • Navigation

Search:

Type: Posts; User: RX7Driver4Life

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    573

    What you want for the block? location?

    What you want for the block? location?
  2. Replies
    5
    Views
    521

    Perfect. So i can run regular copper up to the O2...

    Perfect. So i can run regular copper up to the O2 sensor wires with no problem?
  3. Replies
    5
    Views
    521

    O2 Sensor Wiring

    I was reading into O2 sensor wiring and read that the leads on the O2 sensor are steel not copper. Me engine harness was cut at the O2 sensors and I just have a regular 16awg wire from the engine...
  4. o2 sensors are not hooked up yet.

    o2 sensors are not hooked up yet.
  5. One Exhaust header hotter than the other.

    I slapped on the headman headers in anticipation of my new exhaust coming in. I proceded to turn the car on to let idle and burn off the exhaust coating, when I notice that one manifold is smoking...
  6. One Exhaust Header Hotter than The Other

    I slapped on the headman headers in anticipation of my new exhaust coming in. I proceded to turn the car on to let idle and burn off the exhaust coating, when I notice that one manifold is smoking...
  7. Replies
    21
    Views
    21,254

    Im there guys built it in around 8 months had to...

    Im there guys built it in around 8 months had to do a head gasket change and a rewire becuase i had thrown it in there.

    6141
  8. i was going to buy one before all this drama with...

    i was going to buy one before all this drama with those guys.
  9. Why hasn't this been removed? aren't they not...

    Why hasn't this been removed? aren't they not sponsors any more?
  10. Replies
    4
    Views
    299

    bump for need of more info

    bump for need of more info
  11. Replies
    4
    Views
    299

    what injectors are the ones used on the lt1...

    what injectors are the ones used on the lt1 Delphi, Siemens, SMP?
  12. Replies
    4
    Views
    299

    Injector O Rings and Seats

    I need to buy new injector o rings and injector seats. Any one have a jegs or summit part number I can use to order?
  13. Replies
    19
    Views
    1,149

    another question The head gasket should not...

    another question

    The head gasket should not interfere with a push rod travel should it? I compared this head gasket with the one that was on there and it is the same regardless of the side its on...
  14. Replies
    19
    Views
    1,149

    valve train is stock

    valve train is stock
  15. Replies
    19
    Views
    1,149

    Hey I might not know much about certain things...

    Hey I might not know much about certain things but when im assembling something if something dose not feel right i check it out. The push rods are stock 1XX mile rods and the guys that had the car...
  16. Replies
    19
    Views
    1,149

    i read how to do it on shbox.com i just was not...

    i read how to do it on shbox.com i just was not sure i was doing it right.
    Can anyone give me some part numbers of pushrods I can buy from summit. Is the stock length 7.195 or 7.200?
  17. Replies
    19
    Views
    1,149

    Ok I tried with the #1 cylinder at TDC to adjust...

    Ok I tried with the #1 cylinder at TDC to adjust the intake valve i spun the push rod and tightened it till i felt drag on the push rod then did a 1/2 turn which 1/2 turn for me is the ratchet at 12...
  18. Replies
    19
    Views
    1,149

    I Hate Rockers......

    Pardon my ignorance for not seeing how they sat before taking them off.

    How do the rockers sit do they go up on the shaft or does the base of them sit on the stud? I am in the process of...
  19. Replies
    29
    Views
    1,746

    Actually I only did the 65 lb tq twice. I did not...

    Actually I only did the 65 lb tq twice. I did not think to check the lower settings twice. Now comes the fun part im going to put on the push rods and the rockers on tomorrow it was to hot today. I...
  20. Replies
    29
    Views
    1,746

    Got the heads on today. Used 9966PT Head gasket,...

    Got the heads on today. Used 9966PT Head gasket, Felpro Bolts and even though they had sealant on them a little extra wont hurt gave them a thin coat of permatex thread sealant. Torqued to 65 ft. lb...
  21. Replies
    29
    Views
    1,746

    Makes for a fun little car. Light weight and lots...

    Makes for a fun little car. Light weight and lots of tq makes for a great daily driver this is what mine is going to be thats why there is an a/c comp. on there i live in Miami its a must LOL. and...
  22. Replies
    29
    Views
    1,746

    http://i196.photobucket.com/albums/aa25/rx7driver4...

    http://i196.photobucket.com/albums/aa25/rx7driver4life/2010-10-04185839.jpg

    http://i196.photobucket.com/albums/aa25/rx7driver4life/2010-10-04185807.jpg
  23. Replies
    29
    Views
    1,746

    Here is what an lt1 looks like in an rx7....

    Here is what an lt1 looks like in an rx7.
    524052415242
  24. Replies
    29
    Views
    1,746

    the heads where checked valve seats replaced and...

    the heads where checked valve seats replaced and mating surface was milled
    5239
  25. Replies
    29
    Views
    1,746

    the bolts say refer to most current factory...

    the bolts say refer to most current factory torque specs for installation.
Results 1 to 25 of 31
Page 1 of 2 1 2